IBM eServer pSeries System 8844 Baseboard Management Controller (BMC) Update Diskette
Version 1.19 (Build ID BYBT19A)


CONTENTS
________

1.0  Overview
2.0  Installation and Setup Instructions
3.0  Configuration Information
4.0  Web Sites and support phone Number
5.0  Trademarks and Notices
6.0  Disclaimer


1.0  Overview
________________________

The 8844 BMC firmware can be updated through the BladeCenter Management
Module web interface.

        1.1     Dependencies:
                - none


2.0  Installing and Setup Instructions
______________________________________

		
    **********  REQUIRED: MAKE SURE THE BLADE IS POWERED OFF AND ALL BLADES **********
    **********            ARE DISCOVERED BEFORE FLASHING                    **********

	2.1.1 To install the BladeCenter Integrated System Management Processor firmware
	      from the BladeCenter Management Module web interface, perform the following steps:

		a). Open a Web browser. In the address or URL field, type the IP address
                    or host name of the Management Module to which you want to connect. The 	 
		    Enter Network Password window opens.
	
		Note: The Management Module defaults to DHCP. If a DHCP host is unavailable, 
		the Management Module assigns a static IP address of 192.168.70.125.
	
		b). Type your user name and password in the Enter Network Password 
		    window. 
	
		c). Select a timeout value, in minutes, in the field provided.   If your 
		    browser is inactive for that number of minutes, the Management Module logs 
		    you off the Web interface.

		d). Click Continue to start the session. The browser opens the System 
		    Health page, which gives you a quick view of the system status. 

		e). In the navigation frame, click Firmware Update under Blade Tasks,
		    select the Target blade slot number, then click Browse.

		f). Switch to the drive and directory containing the unpackaged files. 
		    Navigate to the PKT file you want to update, named as:

		       BYBTxxy.PKT    (Where xx = build ID, and y = revision)
	    
		g). Click Open. The file (including the full path) appears in the box 
		    beside Browse.

		h). To begin the update process, click Update. A progress indicator
		    opens as the file is transferred to temporary storage. A confirmation page 	
		    opens when the file transfer is completed and the BladeCenter Integrated 
		    System Management Processor has been restarted.
	
		  *** Note: To cancel this process at any point, click Cancel ***

	2.1.2 In Case of a failed RS485 (remote) flash
	
		a). Only one blade can be in kernel mode in a chassis at one time.
	
		b). The Management Module has known issues if a flash fails.  The easiest 
		    way to recover is to:
			1). Pull the failed blade from the chassis
			
			2). Reset the MM 
			
			3). Reinsert the failed blade
			
			4). Retry the flash on the failed blade after the blades have all 	
			    been discovered.

	
3.0  Configuration Information
__________________________________________

        3.1 	Level of Recommendations and Prerequisites for proper blade operation:

		- System Firmware version MB240_470 010, or newer.
		- Broadcom NIC boot code version 3.18, or newer.
		- Broadcom IPMI-PT code version 6.08, or newer.
		- Management Module 1 version BRET85F, or newer.
		- Management Module 2 version BPET14A, or newer.
		

4.0  WEB Sites and Support Phone Number
__________________________________________

        4.1     IBM Support Web Site:
                http://www.pc.ibm.com/support

        4.2     IBM eServer pSeries Web Site:
                http://www.ibm.com/eserver/pseries

        4.3     If you have any questions about this update, or
                problems applying the update, go to the following
                Help Center World Telephone Numbers and URL:
                http://www.pc.ibm.com/qtechinfo/YAST-3P2QYL.html.


5.0. TradeMarks and Notices
______________________________

        5.1     The following terms are trademarks of the IBM
                Corporation in the United States, or other countries
                or both:
                            * IBM
                            * Netfinity
                            * Netfinity Manager
                            * Advanced System Management

                Other company, product, and service names may be
                trademarks or service marks of others.


6.0. Disclaimer
__________________

        6.1     THIS DOCUMENT IS PROVIDED "AS IS" WITHOUT WARRANTY OF
                ANY KIND.  IBM DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS
                OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED
                WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND
                MERCHANTABILITY WITH RESPECT TO THE INFORMATION IN
                THIS DOCUMENT.  BY FURNISHING THIS DOCUMENT, IBM
                GRANTS NO LICENSES TO ANY PATENTS OR COPYRIGHTS.

        6.2     Note to Government users:

                Note to U.S. Government users-- Documentation related
                to restricted rights-- Use, duplication and disclosure
                is subject to restrictions set forth in GSA ADP Schedule
                Contract with IBM Corporation.


